[2026] HPE7-A06 Dumps are Available for Instant Access [Q38-Q62]

NEW QUESTION 38
A customer has configured eBGP peering using local AS 65000 with two routers from a CX 6300 VSF stack with thefollowing switch ports:
[ports connecting to router-1 10.10.10.2]

The LAGs are connected lo third-party L2 switches, which are used as a transit network for the remote eBGP routers. To optimise the possible BGP peering issues. The AOS-CX switch Is configured with theglobal settings:

What needs to be done on the AOS_CX switch to enable the bidirectional forwarding with the eBGP peers?

Option A

Option B

Option C

Option D

NEW QUESTION 39
Which command will permit read-only access to a user with physical access to an AOS-CS switch?

NEW QUESTION 40
A customer is trialing the below colorless port configuration on a single switch and has noticed that users roaming to access points connected to the test switch are unable to receive an IP address on the corporate Wi- R network, which is operating in bridged mode All other SSIDs are working as expected and the AP is Online in HPE Aruba Networking Central.
The security team reports that there have been no failed authentications m HPE Aruba Networking ClearPass Access Tracker and that the last entry for the wiredport is returning the KADIUS Aruba-User-Hold attribute
‘Access_Point.
Which configuration change is required to resolve the issue?

port-access client-move enable

interface 1/1/1-1/1/48
aaa authentication port-access client-limited 0

interface 1/1/1/1-1/48
port-access onboarding-method concurrent enable

port access role Access_point auth-mode device-mode

The issue involves users roaming to APs connected to a test switch failing to receive an IP address on the corporate Wi-Fi network (bridged mode), with ClearPass reporting a RADIUS Aruba-User-Role attribute of Access_Point. The goal is to identify the configuration change needed to resolve this issue.
* Analysis of Options:
* Option A (port-access client-move enable):Enables client movement between ports but does not address the AP authentication issue.
* Option B (aaa authentication port-access client-limit 0):Correct. Setting the client limit to 0 on the switch ports (1/1/1-1/1/48) disables MAC authentication for APs, allowing them to be treated as trusted devices and preventing the application of an incorrect role.
* Option C (port-access onboarding-method concurrent enable):Enables concurrent onboarding but is unrelated to the AP role issue.
* Option D (port-access role Access_point auth-mode device-mode):Configures a device mode role but does not resolve the IP assignment issue caused by incorrect authentication.
* Why Option B is Correct:The issue arises because the switch is applying 802.1X or MAC authentication to the AP ports, resulting in ClearPass assigning the Access_Point role, which restricts client connectivity. By setting aaa authentication port-access client-limit 0 on the AP-connected ports (1
/1/1-1/1/48), the switch disables port-access authentication for these ports, treating the APs as trusted devices. This allows clients to authenticate properly via the AP and receive IP addresses in bridged mode, resolving the issue.
* Relevance to Certification Objectives:
* WLAN (9%):Involves troubleshooting wireless functions and Layer 2 issues related to AP connectivity.
* Authentication/Authorization (9%):Includes troubleshooting ClearPass integration and 802.1X configurations.
* Security (10%):Covers troubleshooting wired 802.1X implementations.
References:
HPE Aruba Networking AOS-CX Configuration Guide: Port Access Authentication, detailing client-limit configuration.
HPE7-A06Study Guide: Covers ClearPass integration and AP authentication troubleshooting.
HPE Aruba Networking Technical Documentation: Dynamic Segmentation and Port Access Security.

NEW QUESTION 41
Refer to the exhibit.

A gateway cluster needs to be connected to the VSX-enabled switches where MC-LAG is configured What Is a possible constraint?

lacp mode active needs to be configured on the gateways when usingstatic-activate” mode.

The command lacp fallback is missing on the interface lag level.

LLDP needs to be enabled to detect LACP-configured interfaces.

LACP is not supported during the initial provisioning and needs to be turned off.

NEW QUESTION 42
Match the BGP connection slates to the conditions thatcould have caused that state.

Explanation:
The router is able to process update messages. –>established
The router is waiting for the neighbor’s open message. –>open sent
Routers have agreed on matching feature sets. –>open confirm
The session establishment has timed out. –>idle
This question requires matching BGP connection states from the BGP Finite State Machine (FSM) to descriptions of conditions that occur within or lead to those states.
* Idle:This is the initial state where BGP awaits a start event or retries after a failure. It’s also the state entered upon error detection or session closure, including timeouts during connection attempts.
* Matches:”The session establishment has timed out.” – A timeout during the connection process forces the BGP process back to the Idle state to potentially retry later.
* OpenSent:After a TCP connection is established, the local router sends a BGP OPEN message with its parameters (AS number, capabilities, etc.) and transitions to the OpenSent state while waiting to receive an OPEN message from its BGP neighbor.
* Matches:”The router is waiting for the neighbor’s open message.”
* OpenConfirm:Once the router receives an OPEN message from its neighbor and validates the parameters (e.g., matching AS, compatible capabilities), it sends a KEEPALIVE message and moves to the OpenConfirm state. It waits for a KEEPALIVE from the neighbor to confirm the session. Basic parameter checks and capability negotiations are successfully completed in this phase.
* Matches:”Routers have agreed on matching feature sets.” – This agreement happens upon successful validation of the OPEN messages exchanged.
* Established:This is the final, stable state where BGP peering is successful. Both routers have accepted each other’s parameters via the OPEN messages and confirmed the session with KEEPALIVEs. In this state, the routers can exchange UPDATE messages containing routing information.
* Matches:”The router is able to process update messages.”
References:RFC 4271 (BGP4 specification – Section 8, Finite State Machine), BGP configuration and troubleshooting guides for AOS-CX. This relates to the “Routing” (16%) and “Troubleshooting” (10%) objectives.

NEW QUESTION 43
The user’s device is failing 802.1 Xwith EAP-TLS authentication. We know that theclient-side certificate is valid. What is the likely cause of this issue? (Select two.)

The user’s device is not configured to use the correct gateway.

There is a problem with the ACL applied to the switch port

There Is an EAP-type mismatch.

The user’s device is using the wrong MAC address

The NAD is not able to communicate with DNS servers.

NEW QUESTION 44
When using the cable diagnostic feature on an AOS-CX switch to test a 1000BaseT connection, whatthe accuracy of ‘distance to fault”?

+/- 10m

+/- 2m

+/-6m

+/-1m

NEW QUESTION 45
A client is unable to connect to the network, In the HPE Aruba Networking ClearPass access tracker, wo can seean EAP timeout What is a possible cause of this message?

The radius server doesnot trust the client certificate

The radius server can seethat theclient certificate is expired.

The client can see that theradiusserver certificateis expired.

The client does not trust the radius server certificate.

NEW QUESTION 46
An IT administrator uses AOS-CX switches to send TCP 22 trafficfrom the switch port to a remoteserver for analysis. The administrator now wants to save it locally tobedownloaded and used later in case the admin changes their mind about the approach to take.

destination file tshatk-pcap

destination tunnel file tshark-pcpap

destination cpu

destination flash:/.’my-mirror.pcnap policy Policy Minor22

NEW QUESTION 47
Which EAP methods arc supported when configuring The 802.1X supplicant feature on an AOS-CX switch?
(Selecttwo.)

EAP-TLS

EAP-TTLS

EAP-MD5

EAP-PEAP

EAP-TEAP

NEW QUESTION 48
Exhibit.

AGG-SW1 and AGG-SW2 are configured with iBGP and eBGP to AS65000. Both agg-sw1 and agg-sw2 useroute-map BGP-EXPORT and ip-prefix list local-export in the bgp configuration.
What must be done on agg-swl for the adjacent router to prefer to route all exported routes by agg-sw2?

Add set local-preference 200 to the route-map BGP-EXPORT

Add set as-path prepend 65345 65345 65345 65345 to the route-map BGP-EXPORT Match with local- export Ip prefix-list.

Add set metric 200 to the route-map BGP-EXPORT.

Add set as-path 65345 65345 65345 65345 to the route-map BGP-EXPORT Match with local-export ip prefix-list.

The goal is to make the adjacent router prefer routes exported by AGG-SW2 over AGG-SW1 for iBGP and eBGP routes to AS65000. Both switches use a route-map BGP-EXPORT with an ip-prefix list local-export.
BGP path selection uses attributes like local preference, AS path length, and metric to determine the preferred route.
* Analysis of Options:
* Option A:Setting local-preference 200 affects iBGP route selection within the same AS but has no impact on eBGP peers (external AS65000), as local preference is not advertised externally.
* Option B:Prepending the AS path with 65345 65345 65345 65345 increases the AS path length for routes exported by AGG-SW1, making them less preferred by the adjacent router (both iBGP and eBGP peers) compared to AGG-SW2’s routes, which have a shorter AS path.
* Option C:Setting metric 200 affects the MED (Multi-Exit Discriminator), which is used for eBGP route selection within the same AS but is less influential than AS path length and not applicable for iBGP.
* Option D:Incorrect syntax (set as-path without prepend) and does not achieve the desired effect.
* Why Option B is Correct:BGP route selection prioritizes the shortest AS path for both iBGP and eBGP. By prepending AS 65345 multiple times to AGG-SW1’s exported routes, AGG-SW1’s routes appear less attractive due to a longer AS path, causing the adjacent router to prefer AGG-SW2’s routes.
This is a standard BGP traffic engineering technique.
* Relevance to Certification Objectives:
* Routing (16%):Involves designing and troubleshooting BGP routing topologies, including manipulating path attributes like AS path.
* Troubleshooting (10%):Includes remediating BGP routing issues by adjusting route-maps.
References:
HPE Aruba Networking AOS-CX Configuration Guide: BGP Configuration, covering route-maps and AS path prepending.
HPE7-A06Study Guide: Details BGP path selection and traffic engineering.
HPE Aruba Networking Technical Documentation: BGP Route Manipulation, explaining AS path prepending for route preference.

NEW QUESTION 49
You are configuring an SSID that is using PSK as a security mechanism. Why should you use WPA3- Personal with WPA3 Transition Mode disabled?

WPA3-Porsonal with Transition Modedisabled is optional tor 6 GHz-enabled networks as there is a built-in tailback to 6 GHz mode with WPA2

WPA3-Personal with Transition Mode disabled is mandatory for 6 GHz-enabled networks.

WPAS-Personalwith Transition Mods disabled is mandatory for 5 GHz-enabled networks.

WPA3-Porsonal with Transition Mode disabled should be used to prevent legacy clients from connecting to thenetwork.

NEW QUESTION 50
AnOSPF router has teamed a path to an external network oy both an El and an E2 advertisement, both routes having the same path cost. Which path -will the router prefer?

The router will use both paths equally by means ofECMP

The router will prefer the E2 path.

Both routes will be suppressed until the path conflict has been resolved.

The router will prefer the E1 path.

NEW QUESTION 51
A customer hassot a requirement for VLAN 151 to be an isolated VLAN. A colleague has copied and pasted a partialconfiguration, but you do not achieve the desired outcome. This is the code that was added:
What should be added to the configuration before this code to achieve the desired result?

The customer requires VLAN 151 to be configured as an isolated Private VLAN. A partial configuration was added, but the desired outcome wasn’t achieved. We need to determine which configuration snippet should be addedbeforethe (unspecified) partial configuration to correctly set up the Private VLAN structure.
* Private VLAN Configuration Fundamentals:
* APrimary VLANmust be defined. This VLAN carries traffic between promiscuous ports and ports in associated secondary VLANs.
* Secondary VLANs(either isolated or community) are associated with the primary VLAN.
* Ports are then mapped to either the primary VLAN (promiscuous ports, typically router/firewall connections) or a secondary VLAN (host ports). Isolated ports within thesameisolated VLAN cannot communicate with each other.
* Analyzing the Options (Assuming VLAN 15 is the intended Primary):
* A)
vlan 15
private-vlan primary
vsx-sync
This correctly defines VLAN 15 as the Primary Private VLAN. The vsx-sync command ensures this configuration is synchronized across a VSX pair (relevant if applicable). This is the necessary prerequisite before defining VLAN 151 as an isolated secondary VLAN and associating it with VLAN 15.
* B)isolated-vlan primary is incorrect syntax. The command is private-vlan primary.
* C)primary-vlan isolated 151 is incorrect syntax for defining either the primary or secondary VLAN type/association within the primary VLAN context.
* D)private-vlan isolated 151 within the vlan 15 context is incorrect syntax. The private-vlan isolated command belongs under the configuration of the secondary VLAN (VLAN 151 in this case).
* Conclusion:Before configuring VLAN 151 as private-vlan isolated and associating it, the primary VLAN must be defined. Option A correctly shows the command (private-vlan primary) under the intended primary VLAN’s configuration (vlan 15) to establish it as the primary VLAN.
References:AOS-CX Security Guide (Private VLAN configuration steps and commands). This relates to the
“Switching” (19%) and “Security” (10%) objectives.

NEW QUESTION 52
Which is a best practice for configuringGBP?

Configure GBP classes to have a destination role that is different from theassociated user role.

Use static user roles (SUR) to configure GBP

Configure GBP classes to have a destination role that is the same as the associated user rote.

Use downloadable user roles (DUR) to configure GBP.

NEW QUESTION 53
You haverecently configured a switch for 802.IX authentication with HPE Aruba Networking ClearPass. A security admin is seeing events withthe following description in ClearPass Event Viewer.
RADIUS authentication attempt from unknown NAD (10.10.1.10:1812)’
Which command should you us to identify theconfiguration issue?

show ip source-interfaceradius

show aaa authentication-server radius

show radius-server shared-secret

show radius-server detail

NEW QUESTION 54
A client would like to usetheHPE Aruba Networking Switch MultiEdit Software function in HPE Aruba Networking Central. Which option is available?

Usetemplates and apply them to selected switches.

Apply a configuration to an interface range for selected switches.

Run the same NAE scripts for selected switches.

Use CLI scripts and apply them to selected switches.

The question involves a client wanting to use the HPE Aruba Networking Switch Multi-Edit Software function in HPE Aruba Networking Central to manage multiple switches. The task is to identify the available option.
* Analysis of Options:
* Option A (Use templates and apply them to selected switches):Incorrect. Templates are used for configuration management in Central but are not part of the Multi-Edit Software function.
* Option B (Apply a configuration to an interface range for selected switches):Incorrect. Multi- Edit focuses on CLI scripting, not specifically interface range configurations.
* Option C (Run the same NAE scripts for selected switches):Incorrect. Network Analytics Engine (NAE) scripts are for monitoring, not configuration via Multi-Edit.
* Option D:Correct. Multi-Edit Software in Central allows administrators to apply CLI scripts to multiple selected switches for configuration changes.
* Why Option D is Correct:HPE Aruba Networking Central’s Multi-Edit Software feature enables administrators to create and apply CLI scripts to multiple AOS-CX switches simultaneously, streamlining configuration tasks. This is particularly useful for bulk changes, such as VLAN configurations or policy updates, across selected switches. The feature supports direct CLI input or script uploads, ensuring consistent application of commands, as per HPE Aruba Networking’s management tools. This aligns with the client’s need for efficient multi-switch management.
* Relevance to Certification Objectives:
* Connectivity (9%):Developing configurations for multiple devices based on customer requirements.
* Troubleshooting (10%):Applying consistent configurations to resolve network issues.
* Network Stack (4%):Analyzing solutions for network management automation.
References:
HPE Aruba Networking Central User Guide: Multi-Edit Software Feature, detailing CLI script application.
HPE7-A06Study Guide: Covers network management tools in Central.
HPE Aruba Networking Technical Documentation: Multi-Edit Software Best Practices.

NEW QUESTION 55
Two CX 8325 switches are configured as a cluster using VSX for the coreroleand two CX 6300M in VSF for theaggregation role. When a minor software upgrade is issued on the switches, what isthe method to achieve a hitlessupgrade with the aggregation switches?

VSF update-software initiates the software Upgrade first on the secondary switch, followed by the primary.

ISSU update-software initiates the upgrade first on thesecondary switch, Followed by theprimary.

VSF update-software initiates thesoftware upgrade first on the primary switch. followed by the secondary.

ISSU update-software initiates the upgrade first on the primary switch, followed by the secondary.

NEW QUESTION 56
The clientwouldlike to automate the process of troubleshooting issues to have better visibility. Which solution would you recommend for your client?

HPE Aruba Networking F3bric Compose

HPE Aruba Networking Switch Multi-Edit Software

Automate processes with scripting like Python.

AlOps integrated into HPE Aruba Networking Central

NEW QUESTION 57
What is the best practice for using Dynamic Segmentation?

Use UBT to create isolated networks foe specific typos of devices.

Use a combination of role-based access and overlay technologies to create a layered security approach.

Use Dynamic Segmentation only on devices thatare connected to the network via Wi-Fi.

Use LUR to assign roles to devices based on their location and DUR to assign roles to devices based on their user identity.

NEW QUESTION 58
A customer wants to deploy loT security devices that are PoE-powered. Dueto its criticality. it is required that those devices remain active even during a switch software upgrade. What is a valid solution to meet customer requirements?

a VSX pairof switches for redundancy

power-over-ether net quick-poe

power-over-ethernet always-on

power-over-ethernel priority

NEW QUESTION 59
Exhibit.

After Implementing a distributed overlay with distributed anycast gateways, you noticed that toomany ARP packets are being replicated to every access (leaf) switch Which command can you use to optimize the network?

vlan 10 arp-suppression vlan 11 arp-suppression

evpn arp-suppression

evpn ip proxy-arp

interface vlan 10 ip proxy-arp interface vlan 11 ip proxy-arp

NEW QUESTION 60
Exhibit.

After an initial setup of CX 8325 VSX configuration, the active gateway is set up for SVI 10. For testing purposes. SVI 10 on sw-aggi is shut down while traffic from the client connected to Edge-1 is initiated towards the default route.
What is the expected behavior white performing this test?

Traffic is potentially dropped between the client and the destination.

Traffic is forwarded over the ISL without the risk of dropped packets.

Traffic Is unaffected and a 50nsfailover time is expected for agg-sw2 to start traffic forwarding.

Traffic is dropped and vsx-sync will disable SVI10 on agg-sw2 automatically.

NEW QUESTION 61
A pair of CX 8325 series switches a configured in a VSX cluster. Which function is executed on both VSX members during normal operation?

replies to ARP requests with thecluster vMAC

routes PIM and PIM-DR

relays DHCP requests or serves DHCP offer

periodically sends gratuitous ARP and broadcast hello packets

NEW QUESTION 62
The customer is experiencing periodic uplink congestion between campus-1’s AGG-1 and core. This has boon negativelyaffecting voice communications.The VOIP phones edge mark their packets with DSCP EF. The uplink from AGG-1 to core is LAG1.
The customer has already configured the following class and policy on AGG-1:

Based on this policy, which scrip), when deployed on AGG-1. will improve the reliable forwarding of voice trafficbetween AGG-1 and its uplink to the core?

Leave a Reply Cancel reply