Read Online PD1-001 Test Practice Test Questions Exam Dumps [Q91-Q106]

Rate this post

Read Online PD1-001 Test Practice Test Questions Exam Dumps

Easily To Pass New PD1-001 Premium Exam Updated [Jul 28, 2022]

Q91. Which of the following steps occurs immediately after the writing process?

Charging

Fusing

Developing

Transfer

Q92. On a monochrome printer, which of the following type of image would a technician see if the primary charge is not applied to the drum during the charging process?

Black Pages

Reversed Image

Blank Pages

Ghost Image

Q93. If the paper is jamming in the fuser, which of the following actions should be performed? (Select TWO).

Check the registration roller for excess wear.

Check for foreign material in the fuser.

Check the feed unit rollers for excess wear.

Check the photoconductor for contamination.

Check the hot roller for excess wear.

Q94. After developing, which of the following is the next step in the print process?

Transfer

Charging

Fusing

Writing

Q95. Which of the following information can be found on a printer configuration page? (Select THREE).

Operating System Test Page

Print Quality information

Firmware Versions

Page Counts

Available fonts

Network Settings

Q96. Which of the following runs a multi-functional device (MFD)?

Firmware

ROM

RAM

BIOS

Q97. Which of the fol owing conditions is MOST likely to affect the transmission speed (baud rate) of a fax device?

Quality of phone line

Resolution

Amount of pages

Color images

Q98. Which of the following is a reason for color capable printing devices to have color calibration?

To match the workstations monitor to Pantone color standards

To match the workstations monitor to a standard test sheet

To match the printed image colors to the original image colors

To match the printed image to another devices color input

Q99. Which of the following failed components will cause an accordion jam in the fuser?

Pawls

Ball bearing

Halogen lamps

Thermistor

Q100. If a print coming out from the device has regular, evenly spaced, dark marks in the direction of the media feed; the cause of the problem is from:

a nick in the fuser heat roller.

toner spil ing from the cleaner section.

a mark on the platen glass.

an incorrect media setting.

Q101. A customer reports their MFP has dark print quality when copying, but when printing, the quality is good. Which of the following is the BEST way to determine where the problem might be located?

Review the adjustment log to see if there have been any changes to the settings.

Attempt to recreate the problem by printing an internal page and copying a page.

Suggest to the customer that they should only print from this model.

Use various paper trays and finishing options to see if the problem follows any pattern.

Q102. Which of the following is required in order for the primary charging process to fully charge the surface of the photoconductor?

The developing spacer rollers must be in contact with the photoconductor.

The charging corona/roller must have continuity to device ground.

The photoconductor must have continuity with device ground.

The photoconductor must be in contact with the cleaning blade.

Q103. If the specification for the metering blade adjustment in the developer unit is .7 mil imeters, and it is actual y adjusted to .4 millimeters, which of the following image quality problems would MOST likely be seen?

High density image

Low density image

Black image

White image

Q104. A wrap spring clutch transmits drive to a roller by:

turning on a motor.

magnetism.

releasing the sleeve that surrounds the spring.

expanding the spring inside the sleeve.

Q105. In which of the following sections of the MFD would a Teflon coated roller be found?

The paper feed unit

The ADF assembly

The manual feed tray

The fuser unit

Q106. While troubleshooting a paper jam, the technician checks the service manual to determine which trays use the roller where the jam occurs. Which of the following general troubleshooting steps does this process describe?

Establishing theory of probable cause

Document the solution

Validation of the issue

Trying to recreate the problem

Loading …

PD1-001 Certification All-in-One Exam Guide Jul-2022: https://www.testsimulate.com/PD1-001-study-materials.html

Leave a Reply Cancel reply