[May 10, 2023] Valid 350-501 Test Answers & Cisco 350-501 Exam PDF [Q145-Q167]

NEW QUESTION 145
Drag and drop the NAT64 descriptions from the left onto the correct NAT64 types on the right.

NEW QUESTION 146
Refer to the exhibit:

A network operator working for service provider with an employee id 3715 15:021 applied this configuration to a router.
Which additional step should the engineer use to enable LDP?

Disable Cisco Express Forwarding globally

Delete the static router ID

Enable MPLS LDP on the interface

Configure the both keyword to enable LDP globally

NEW QUESTION 147
Refer to the exhibit.

A network engineer is configuring customer edge routers to finalize a L2VPN over MPLS deployment Assume that the AToM L2VPN service that connects the two CEs is configured correctly on the service provider network Which action causes the solution to fail?

A loopback with a /32 IP address has not been used

OSPF does not work with L2VPN services

The x connect statement has not been defined

The routing protocol network types are not compatible

NEW QUESTION 148
Refer to the exhibit.

What is the result of this configuration?

Router 1 opens and closes a TCP connection to the TACACS+ server every time a user requires authorization.

Router 1 and the TACACS+ server maintain one open connection between them only when network administrator is accessing the router with password ciscotest.

Router 1 and the TACACS+ server maintain one open connection between them.

Router 1 opens and closes a TCP connection to the TACACS+ server every time a user requires authentication.

NEW QUESTION 149
Refer to the exhibit:

Which configuration prevents the OSPF neighbor from establishing?

mtu

duplex

network statement

default-metric

NEW QUESTION 150
What do Chef and Puppet have in common?

use Ruby

use a master server

require modules to be created from scratch

manage agents referred to as minions

NEW QUESTION 151
Refer to the exhibit. Router 1 and router 2 are running BGP. and router 2 and router 3 are running OSPF Area 0. Router 1 is advertising loopback interlaces Lo 0 and lo 2. and router 2 is redistributing BGP into OSPF Area 0.
Which configuration must an administrator apply so that router 2 uses a route map to redistribute only the internal route from Lo 2?

NEW QUESTION 152
Which additional feature does MPLS DiffServ tunneling support?

matching EXP and DSCP values

interaction between MPLS and IGP

using GRE tunnels to hide markings

PHB layer management

NEW QUESTION 153
Refer to the exhibit.

What is the effect of this configuration?

R1 supports a graceful restart operation on the peer, even if graceful restart is disabled on the peer.

R1 supports a peer that is configured for LDP SSO/NSF as the peer recovers from an outage.

R1 failovers only to a peer that is configured for LDP SSO/NSF.

R1 failovers to any peer.

NEW QUESTION 154
ASN 65001 is peering with ASN 65002 to exchange IPv6 BGP routes. All routes that originate in ASN 65001 have a standard community value of 65001:100, and ASN 65002 is allowed to advertise only 2001 :db8:aaaa::/48. An engineer needs to update the ASN 65001 route-filtering configuration to meet these conditions:
* Looped routes into ASN 65001 and routes that have traversed 10 or more ASNs must be denied.
* Routes accepted into ASN 65001 must be assigned a community value of 65001:200.
Which configuration must the engineer apply to the ASN 65001 border router?

Option A

Option B

Option C

Option D

Option E

NEW QUESTION 155
Refer to the exhibit. Router BRDR-1 is configured to receive the 0.0.0.0/0 and 172.17.1.0/24 networks via BGP and advertise them into OSPF area 0. An engineer has noticed that the OSPF domain is receiving only the 172.17.1.0/24 route and default route 0.0.0.0/0 is still missing. Which configuration must an engineer apply to resolve the problem?

router ospf 1 redistribute bgp 65001 metric 100 route-policy BGP-TO-OSPF end

router ospf 1 default-information originate end

router ospf 1 default-metric 100 end

router ospf 1 default-information originate always end

NEW QUESTION 156
Which function does RSVP perform in a Cisco MPLS TE environment?

It establishes targeted LDP sessions between neighbors that are directly connected.

It signals to LDP protocol along the path that a Cisco MPLS TE will be configured.

It reserves bandwidth for LDP sessions between routers participating in a Cisco MPLS TE.

It reserves the bandwidth along the path between the head-end and tail-end router.

NEW QUESTION 157
Refer to the exhibit.

An engineer is configuring router R1 for OSPFv3 as shown. Which additional configuration must be performed so that the three active interfaces on the router will advertise routes and participate in OSPF IPv6 processes?

from 2.2.2.2, with a TTL of less than 2

to 2.2.2.2, with a TTL of less than 253

from 2.2.2.2, with a TTL of 253 or more

to 2.2.2.2, with a TTL of 2 or more

NEW QUESTION 158
Drag and Drop Question
Drag and drop the methods of Cisco MPLS TE tunnel traffic assignment from the left onto their characteristics on the right.

NEW QUESTION 159
Refer to the exhibit:

This configuration is being applied on an IOS XR router.
Which statement about this configuration is true?

It is used to set up configuration to poll network data

It is used to enable gRPC

It is used to create a streaming subscription with a 60-second interval

It is used to create a streaming subscription with a 600-second interval

NEW QUESTION 160
Drag and Drop Question
Drag and drop the functions from the left onto the correct Path Computation Element Protocol roles on the right.

NEW QUESTION 161

Refer to the exhibit. An engineer is preparing to implement data plane security configuration.
Which statement about this configuration is true?

Router 2 is the router receiving the DDoS attack.

Router 1 must be configured with uRPF for the RTBH implementation to be effective.

Router 1 is the trigger router in a RTBH implementation.

Router 2 must configure a route to null 0 for network 192.168.1.0/24 for the RTBH implementation to be complete.

NEW QUESTION 162
Refer to the exhibit. R101 is peering with R102 and R103, and R201 is peering with R202 and R203 using iBGP Labeled Unicast address families.
The OSPF area 0 border routers are in a full iBGP Labeled Unicast mesh, and VPNv4 routes are exchanged directly between PE routers R101 and R201 through iBGP.
Which address family-level configuration must be applied on ABR R102 on ABR R102 to support a Unified MPLS routing architecture with partitioned IGP domains?

NEW QUESTION 163
Refer to the exhibit:

What does this value mean when it is received in XML?

It shows the ending of the script

It indicates a break in a sequence

It indicates a value assigned by a network administrator to tag a route

It means a data fie4d is blank

NEW QUESTION 164
Refer to the exhibit:

A network engineer is implementing a BGP routing policy.
Which effect of this configuration is true?

All traffic that matches acl10 is allowed without any change to its local-preference

All traffic that matches acl10 is dropped without any change to its local-preference

If traffic matches acl10, it is allowed and its local-preference is set to 300

All traffic is assigned a local-preference of 30O regardless of its destination

NEW QUESTION 165
Refer to the exhibit.

Which configuration must be applied to each of the four routers on the network to reduce LDP LIB size and advertise label bindings for the /32 loopback IP space only?

Option A

Option B

Option C

Option D

NEW QUESTION 166
Refer to the exhibit.

Refer to the exhibit. The application server in the data center hosts voice, video, and data applications over the internet. The data applications run more slowly than the voice and video applications. To ensure that all applications run smoothly, the service provider decided to implement a QoS policy on router PER 2 to apply traffic shaping. Which two actions must an engineer take to implement the task? (Choose two.)

Configure the scheduling function to handle delayed packets.

Enable packet remarking for priority traffic.

Configure a queue to buffer excess traffic.

Set the token value for secondary traffic.

Set a threshold to discard excess traffic.

NEW QUESTION 167
What Is one of the differences between Ansible and Chef?

Ansible uses YAML and Chef uses Ruby.

Chef requires the use of Windows in the environment and Ansible requires Linux.

Chef is highly scalable and Ansible is highly secure.

Ansible uses Ruby and Chef uses Python.

Leave a Reply Cancel reply