[Q103-Q118] 350-501 Dumps are Available for Instant Access [2023]

Rate this post

350-501 Dumps are Available for Instant Access [2023]

Practice with these 350-501 dumps Certification Sample Questions

QUESTION 103
Refer to the exhibit. The network engineer who manages ASN 65001 is troubleshooting suboptimal routing to the 198.18.15.0/24 prefix. According to the network requirements:
– Routing to IP destinations in the 198.18.15.0/25 block must be
preferred via the EDGE-1 PE.
– Routing to IP destinations in the 198.18.15.128/25 block must be
preferred via the EDGE-2 PE.
– More specific prefixes of the 198.18.15.0/24 block must not be
advertised beyond the boundaries of ASN 64611.
– Routing to 198.18.15.0/24 must be redundant in case one of the
uplinks on INT-R1 fails.
Which configuration must the network engineer implement on INT-R1 to correct the suboptimal routing and fix the issue?

configure terminal
route-policy ASN65001-SPECIFIC-OUT
if destination in (198.18.15.0/25) then
set community (no-export, peeras:65001)
done
endif
if destination in (198.18.15.0/24) then
prepend as-path 65001 3
done
endif
drop
end-policy
!
router bgp 65001
neighbor 100.65.0.1
address-family ipv4 unicast
route-policy ASN65001-SPECIFIC-OUT out
end

configure terminal
route-policy ASN65001-SPECIFIC-OUT
if destination in (198.18.15.0/25) then
set community (internal, peeras:65001)
done
endif
if destination in (198.18.15.0/24) then
done
endif
drop
end-policy
!
router bgp 65001
neighbor 100.65.0.1
address-family ipv4 unicast
route-policy ASN65001-SPECIFIC-OUT out
end

configure terminal
route-policy ASN65001-SPECIFIC-OUT
if destination in (198.18.15.0/25) then
set community (no-advertise, peeras:65001)
done
endif
if destination in (198.18.15.128/25) then
prepend as-path 65001 3
done
endif
drop
end-policy
!
router bgp 65001
neighbor 100.65.0.1
address-family ipv4 unicast
route-policy ASN65001-SPECIFIC-OUT out
end

configure terminal
route-policy ASN65001-SPECIFIC-OUT
if destination in (198.18.15.0/25) then
set community (no-export, peeras:65001)
done
endif
if destination in (198.18.15.128/25) then
prepend as-path 65001 3
done
endif
drop
end-policy
!
router bgp 65001
neighbor 100.65.0.1
address-family ipv4 unicast
route-policy ASN65001-SPECIFIC-OUT in
end

QUESTION 104
In an MPLS network, which protocol can be used to distribute a Segment Prefix?

LDP

EIGRP

OSPF

RSVP-TE

QUESTION 105
A network engineer is configuring a BGP route policy for the SUBNET prefix set. Matching traffic must be dropped, and other traffic must have its MED value set to 400 and community 4:400 added to the route. Which configuration must an engineer apply?

Option A

Option B

Option C

Option D

QUESTION 106
Drag and drop the technologies from the left onto the correct definitions on the right.

QUESTION 107
Refer to the exhibit. Which task completes the configuration?

Specify the maximum number of prefixes that R1 receives from neighbor 192.168.1.2.

Specify the source interface in the neighbor statement.

Specify the activate neighbor 192.168.1.2 under the IPv4 address family.

Specify the local-as value in the neighbor statement.

QUESTION 108
A network administrator is planning a new network with a segment-routing architecture using a distributed control plane. How is routing information distributed on such a network?

Each segment is signalled by an SR controller, but each segment makes Its own steering decisions based on SR policy.

Each segment is signalled by MPLS, and each segment makes steering decisions based on the routing policy pushed by BGP.

Each segment is signalled by an SR controller that makes the steering decisions for each node.

Each segment is signalled by a compatible routing protocol and each segment makes its own steering decisions based on SR policy.

QUESTION 109
Refer to the exhibit:

R1 and R2 are directly connected with Fast Ethernet interfaces and have the above configuration applied OSPF adjacency is not formed. When the debug ip ospf hello command is issued on R1. these log messages are seen.

Which command can be configured on routers R1 and R2 on fO/O interfaces to form OSPF adjacency?

ip ospf network non-broadcast

ip ospf network point-to- multipoint non-broadcast

ip ospf network point-to-point

ip ospf network broadcast

QUESTION 110

Refer to the exhibit. Which purpose of implementing NSF with this configuration is true?

The router uses NSF to handle RP switchover while allowing neighbor relationships to remain up.

The router uses NSF to reduce neighbor-relationship downtime during RP switchover.

The router uses NSF to load balance traffic on a routed EtherChannel.

The router uses NSF to load balance traffic between two links, with the primary link alternating every 90 seconds.

QUESTION 111
Refer to the exhibit.

Router 1 is missing the route for the router 2 loopback 0. What should the engineer change to fix the problem?

the area numbers on Router 1 and Router 2 to be similar

the wildcard mask network statement in OSPF of Router 2

Router 1 to be an ABR

the hello timers on Router 1 and Router 2 to be different

QUESTION 112
Refer to the exhibit.

While troubleshooting the network, a network operator with an employee id: 3812:12:993 is trying to ping XR1. Which result should the operator expect when trying to ping to an XR1 local address?

ICMP traffic works at a policed rate of 19 bytes per second every 100 ms

All ICMP traffic responds successfully.

All ICMP traffic is dropped.

ICMP traffic works at a policed rate of 19 packets every 100 ms.

QUESTION 113

Refer to the exhibit. A network engineer is implementing QoS services. Which two statements about the qos- group keyword on Cisco IOS XR are true? (Choose two.)

It marks packets for end-to-end QoS policy enforcement across the network.

QoS group marking occurs on the ingress.

The QoS group numbering corresponds to priority level.

QoS group can be used in fabric QoS policy as match criteria.

It cannot be used with priority traffic class.

QUESTION 114
Refer to the exhibit an engineer working for a private telecommunication company with an employee Id: 4065:96:080 upgrades the WAN link between routers ASBR-101 and ASBR-201 to
1Gb by Installing a new physical connection between the Gi3 Interfaces.
Which BGP attribute must the engineer configure on ASBR-201 so that the existing WAN link on Gi2 Is maintained as a backup?

Option A

Option B

Option C

Option D

QUESTION 115
Refer to the exhibit.

An engineer must configure router R2 as the new P router in the network. Which configuration must be applied to R2 to enable LDP-IGP Sync on its L2 IS-IS adjacencies?
A)

B)

C)

D)

Option

QUESTION 116
Refer to the exhibit.

What does the number 2 mean in the configuration?

It dictates the number of sessions that will be open with the SNMP manager

It represents the version of SNMP running.

It indicates two SNMP managers are able to read and write with the agent using community string ciscotest.

It is the numeric name of the ACL that contains the list of SNMP managers with access to the agent.

QUESTION 117

Refer to the exhibit. Which statement describes the effect of this configuration?

It matches HTTP traffic for use in a policy map.

It applies a service policy to all interfaces remarking HTTP traffic.

It creates an ACL named WEB that filters HTTP traffic.

It modifies the default policy map to allow all HTTP traffic through the router.

QUESTION 118
Refer to the exhibit. Router 1 and router 2 are running OSPF Area 0. The router logs on both routers show that the LDP link has flapped.
Which configuration must the engineer apply to the two routers to implement session protection on the link?

Get Instant Access REAL 350-501 DUMP Pass Your Exam Easily: https://www.testsimulate.com/350-501-study-materials.html

Leave a Reply Cancel reply