[Q16-Q36] Valid NSE6_FSW-7.2 Practice Test Dumps with 100% Passing Guarantee [Feb-2026]

Rate this post

Valid NSE6_FSW-7.2 Practice Test Dumps with 100% Passing Guarantee [Feb-2026]

NSE6_FSW-7.2 PDF Dumps Are Helpful To produce Your Dreams Correct QA’s

Fortinet NSE6_FSW-7.2 exam is an industry-recognized certification that validates the skills of network professionals in configuring, managing, and troubleshooting FortiSwitch products. NSE6_FSW-7.2 exam covers a wide range of topics related to FortiSwitch products, and candidates must have experience working with these products before attempting the exam. Passing the NSE6_FSW-7.2 exam demonstrates that a network professional has the knowledge and skills required to ensure the security and performance of their network infrastructure.

Q16. Refer to the exhibit.

What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)

Maximum value to accept clients DHCP request is configured as per DHCP server range.

FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.

DHCP clients that are trusted by DHCP snooping configured is only one.

Global configuration for DHCP snooping is set to forward DHCP client requests on all ports in the VLAN.

Q17. How is traffic routed on FortiSwitch?

Hardware-based routing on FortiSwitch is handled by the CPU.

FortiSwitch looks up the hardware routing table and then the forwarding information base (FIB).

ASIC hardware routing can only handle dynamic routing, if supported.

Layer 3 routing can be configured on FortiSwitch, while managed by FortiGate.

Q18. Which Ethernet frame can create Layer 2 flooding due to all bytes on the destination MAC address being set to all FF?

The broadcast Ethernet frame

The unicast Ethernet frame

The multicast Ethernet frame

The anycast Ethernet frame

Q19. How are the ‘by VLAN redirect MAC address quarantine’ mode and the ‘by redirect MAC address quarantine’ mode on FortiGate similar?

Both modes move quarantined devices to the quarantine VLAN.

Both modes require firewall policies to block inter-VLAN traffic.

Both modes add quarantined device MAC addresses to the blocked firewall address group.

Both modes block intra-VLAN traffic by FortiGate automatically.

Q20. Exhibit.

LAG and MCLAG are used to increase the available network bandwidth and enable redundancy. How does spanning tree protocol see MCLAG and LAG if they are configured based on the physi-cal view shown in the exhibit? (Choose two)

Switch 1. Switch 2, and Switch 3 are seen as one MCLAG peer group

Switch 3 and Switch 4 uplinks are treated as single interfaces.

Switch 3 and switch 4 are seen as one MCLAG switch client

Switch 1 and Switch 2 both seen as one single switch.

Q21. Which statement about the configuration of VLANs on a managed FortiSwitch port is true?

Untagged VLANs must be part of the allowed VLANs: ingress and egress.

FortiSwitch VLAN interfaces are created only when FortiSwitch is managed by Forti-Gate.

The native VLAN is implicitly part of the allowed VLAN on the port.

Allowed VLANS expand the collision domain to the port.

Q22. Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?

All ports have auto-discovery enabled by default.

No ports are enabled by default for auto-discovery. This must be configured under config switch interface.

The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.

The last four switch ports on FortiSwitch have auto-discovery enabled by default.

Q23. Refer to the diagnostic output:

Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

It is a MAC address of FortiLink interface on FortiGate.

It is a MAC address of a switch that accepts multiple VLANs.

It is a MAC address of an upstream FortiSwitch.

It is a MAC address of FortiGate in HA configuration.

Q24. Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)

Enabling DHCP snooping on a FortiSwitch VLAN ensures requests and replies are seen by all DHCP servers.

switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks.

By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.

Settings related to DHCP option 82 are only configurable through the CLI

Q25. Exhibit.

Which configuration change will allow the managed FortiSwitch to accept SNMP requests from any source?

Create a new local access profile for SNMP only.

Enable SNMP on the internal interface of the switch.

Configure an SNMP host to send SNMP traps.

Add SNMP service on the management interface of the switch.

Q26. Which statement about the IGMP snooping querier when enabled on a VLAN is true?

Active multicast receiver entries are aging on each IGMP query sent on the VLAN

IGMP reports on the VLAN are forwarded to all switch ports.

The setting can only be enabled using the FortiSwitch CLI.

All other indirectly connected switches will be unable to get IGMP multicast traffic.

Q27. Refer to the exhibits.

You are asked to ensure that managed FortiSwitch devices are reachable by other devices, such as SNMP and other management tools across your network.
Which setting must you configure to ensure traffic from other devices in the network reaches FortiSwitch?

Select a specific default gateway provided to FortiSwitch as an upstream device.

Change the FortiLink interface IP address and DHCP server address range.

Recreate the FortiLink interface with a nonaggregate setting.

Enable NAC settings to select the onboarding VLAN.

Q28. Which is a requirement to enable SNMP v2c on a managed FortiSwitch?

Create an SNMP user to use for authentication and encryption.

Specify an SNMP host to send traps to.

Enable an SNMP v3 to handle traps messages with SNMP hosts.

Configure SNMP agent and communities.

Q29. Which two rules used by MSTP are similar to rules used by other STP methods? (Choose two.)

MSTP uses port role election, similar to rapid STP on the instances.

MSTP uses alternate path and primary path, similar to regular STP.

MSTP uses root bridge selection, similar to rapid STP

MSTP uses timers for transitioning the ports, similar to regular STP.

Q30. What are two ways in which automatic MAC address quarantine works on FortiSwitch? (Choose two.)

FortiSwitch supports only by VLAN quarantine mode.

FortiGate applies the quarantine-related configuration only on FortiGate.

FortiAnalyzer with a threat detection services license is required.

MAC address quarantine can be enabled through the FortiGate CLI only.

Q31. Which packet capture method allows FortiSwitch to capture traffic on trunks and management interfaces?

SPAN

Sniffer profile

sFlow

TCP dump

Q32. What can an administrator do to maintain a FortiGate-compatible FortiSwitch configuration when changing the management mode from standalone to FortiLinK?

Use a migration tool based on Python script to convert the configuration.

Enable the FortiLink setting on FortiSwitch before the authorization process.

FortiGate automatically saves the existing FortiSwitch configuration during the FortiLink management process.

Q33. Exhibit.

Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)

These two routes have a higher administrative distance value available to the destina-tion networks.

These two routes will become primary, if the best routes are removed.

These two routes will be used as load-balancing routes.

These two routes are available in the hardware routing table.

Q34. Which Ethernet frame can create Layer 2 flooding due to all bytes on the destination MAC address being set to all FF?

The broadcast Ethernet frame

The unicast Ethernet frame

The multicast Ethernet frame

The anycast Ethernet frame

Q35. In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)

Switch the FortiLink interface to the target VDOM.

Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.

Create a virtual port pool on the FortiGate CLI.

Assign a port to a VDOM directly on the managed FortiSwitch.

Q36. Which LLDP-MED Type-Length-Values does FortiSwitch collect from endpoints to track network devices and determine their characteristics?

Network policy

Power management

Location

Inventory management

Fortinet NSE6_FSW-7.2 (Fortinet NSE 6 – FortiSwitch 7.2) Exam is an industry-recognized certification that validates the skills and knowledge of network professionals in deploying, configuring, and maintaining FortiSwitch products. NSE6_FSW-7.2 exam is designed for IT professionals who specialize in the implementation and management of network infrastructure and security solutions. Fortinet NSE 6 – FortiSwitch 7.2 certification is ideal for those who want to demonstrate their expertise in FortiSwitch products and enhance their career prospects.

Cover NSE6_FSW-7.2 Exam Questions Make Sure You 100% Pass: https://www.testsimulate.com/NSE6_FSW-7.2-study-materials.html

Leave a Reply Cancel reply