[Jul 05, 2024] 200-301 Dumps Full Questions – Exam Study Guide [Q402-Q416]

Rate this post

[Jul 05, 2024] 200-301 Dumps Full Questions – Exam Study Guide

CCNA Free Certification Exam Material from TestSimulate with 960 Questions

Cisco 200-301 exam is a comprehensive certification exam that tests the candidate’s knowledge and skills in networking. It is a valuable certification for individuals who are interested in pursuing a career in networking or for those who are already working in the field and want to advance their career. Cisco Certified Network Associate Exam certification is recognized worldwide and is highly valued by employers.

NEW QUESTION 402
Which Cisco proprietary protocol ensures traffic recovers immediately, transparently, and automatically when edge devices or access circuits fail?

SLB

FHRP

VRRP

HSRP

NEW QUESTION 403
Drag and Drop Question
Drag and drop the IPv6 address descriptions from the left onto the IPv6 address types on the right. Not all options are used.

NEW QUESTION 404
Which type of traffic Is sent with pure iPsec?

broadcast packets from a switch that is attempting to locate a MAC address at one of several remote sites

multicast traffic from a server at one site to hosts at another location

spanning-tree updates between switches that are at two different sites

unicast messages from a host at a remote site lo a server at headquarters

“The original poster makes a correct observation that EIGRP does not work in a pure IPSEC environment. IPSEC was designed to process unicast traffic.

NEW QUESTION 405
Drag and Drop Question
Drag and drop the Ansible terms from the left onto the right.

NEW QUESTION 406
Drag and drop to the characteristics of networking from the left onto the correct networking types on the right.

NEW QUESTION 407
Refer to the exhibit.

If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command how does the router respond?

It ignores the new static route until the existing OSPF default route is removed

It immediately replaces the existing OSPF route in the routing table with the newly configured static route

It starts load-balancing traffic between the two default routes

It starts sending traffic without a specific matching entry in the routing table to GigabitEthernet0/1

Our new static default route has the Administrative Distance (AD) of 120, which is bigger than the AD of OSPF External route (O*E2) so it will not be pushed into the routing table until the current OSPF External route is removed. For your information, if you don’t type the AD of 120 (using the command “ip route 0.0.0.0 0.0.0.0 10.13.0.1”) then the new static default route would replace the OSPF default route as the default AD of static route is 1. You will see such line in the routing table: S* 0.0.0.0/0 [1/0] via 10.13.0.1

NEW QUESTION 408
Refer to the exhibit.

How does the router manage traffic to 192.168.12.16?

It selects the RIP route because it has the longest prefix inclusive of the destination address.

It chooses the OSPF route because it has the longest prefix inclusive of the destination address.

it load-balances traffic between all three routes

It chooses the EIGRP route because it has the lowest administrative distance

NEW QUESTION 409
DRAG DROP
Drag and drop the WLAN components from the left onto the correct description on the right.

NEW QUESTION 410
Refer to Itie exhibit

A network engineer started to configure port security on a new switch. These requirements must be met:
* MAC addresses must be learned dynamically
* Log messages must be generated without disabling the interface when unwanted traffic is seen
Which two commands must be configured to complete this task”? (Choose two)

SW(ccnfig-if)=switchport port-security mac-address sticky

SW(confKj-if)=switchport port-security violation restrict

SW(config.if)sswitchport port-security mac-address 0010.7B84.45E6

SW(config-if)aswitchport port-security maximum 2

SW(ccnfig-if)=switchport port-security violation shutdown

NEW QUESTION 411
Drag and drop the device behaviors from the left onto the matching HSRP slate on the right.

NEW QUESTION 412

Refer to the exhibit. How does the router manage traffic to 192.168.12.16?

It selects the RIP route because it has the longest prefix inclusive of the destination address.

It chooses the OSPF route because it has the longest prefix inclusive of the destination address.

it load-balances traffic between all three routes

It chooses the EIGRP route because it has the lowest administrative distance

NEW QUESTION 413
Which protocol prompts the Wireless LAN Controller to generate its own local web administration SSL certificate for GUI access?

HTTPS

RADIUS

TACACS+

HTTP

NEW QUESTION 414
Refer to the exhibit. Based on the LACP neighbor status, in which mode is the SW1 port channel configured?

passive

mode on

auto

active

From the neighbor status, we notice the “Flags” are SP. “P” here means the neighbor is in Passive mode.
In order to create an Etherchannel interface, the (local) SW1 ports should be in Active mode.
Moreover, the “Port State” in the exhibit is “0x3c” (which equals to “00111100 in binary format).
Bit 3 is “1” which means the ports are synchronizing -> the ports are working so the local ports should be in Active mode.
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3650/software/release/3se/consolidat ed_guide/command_reference/b_c

NEW QUESTION 415
After a recent security breach and a RADIUS failure, an engineer must secure the console port of each enterprise router with a local username and password.
Which configuration must the engineer apply to accomplish this task?

aaa new-model
line con 0
password plaintextpassword
privilege level 15

aaa new-model
aaa authorization exec default local
aaa authentication login default radius
username localuser privilege 15 secret plaintextpassword

username localuser secret plaintextpassword
line con 0
no login local
privilege level 15

username localuser secret plaintextpassword
line con 0
login authentication default
privilege level 15

NEW QUESTION 416
Refer to the exhibit.

Router R1 resides in OSPF Area 0. After updating the R1 configuration to influence the paths that it will use to direct traffic, an engineer verified that each of the four Gigabit interfaces has the same route to 10.10.0.0/16. Which interface will R1 choose to send traffic to reach the route?

GigabitEthernet0/0

GigabltEthornet0/1

GigabitEthernet0/2

GigabitEthernet0/3

Loading …

Dumps Brief Outline Of The 200-301 Exam: https://www.testsimulate.com/200-301-study-materials.html

Leave a Reply Cancel reply